2025 WIFI Super MB Pro M6+ Pro Full Version DoIP Benz With 1TB HDD for BENZ BMW Software Insatalled on Panasonic FZ-G1 I5 Tablet Ready to Use

Produktbeschreibung

WIFI Super MB Pro M6+ Pro Full Version DoIP Benz With 1TB HDD for BENZ Xentry and BMW ISTA-D ISTA-P Software Plus Panasonic FZ-G1 I5 Tablet Ready to Use

1. With Panasonic FZ-G1 I5 3rd Generation Tablet 8G and BENZ +BMW software 2 in 1, Software Installed Ready to Use
2. Super MB Pro M6+ Pro Full Version= MB Star Full Function+ BMW F+G Series Coding+ Other DoIP

WIFI Super MB Pro M6+ Pro Feture
1.100% compatible with the original Mercedes-Benz software.
2.The front label of the M6+ Pro uses a design with trademark rights and art copyrights to improve product recognition. It  has dded a multi-function switch button to switch to BWM test with one click.
3.The communication between the M6+ Pro and the computer is through a USB3.0 cable or a ethernet cable, which improves the compatibility of the product with computers and tablets. (Compatible with both old and new computers and tablets, no need to choose old-fashioned computers and tablets with network ports.)
4.M6+ Pro supports remote C-side operation. The client does not need to install special diagnostic testing software. Just connect the M6+ Pro to a local computer that can access the Internet, and we can remotely provide customers with paid diagnosis and detection services of vehicle failure. Customers can also set up a local remote diagnostic test in the local area network. The above ways greatly improve the product flexibility.
5.M6+ Pro supports BMW E-SYS, Aicoder, wired and wireless programming and coding of F and G series, and supports BMW modification, hidden functions activation.
6.M6+ Pro supports BMW APP software, provides mobile phone English version of Bimmercode (coding hidden functions activation) Bimmerlink (diagnostics codes clearing) and other mobile phone software, supports MHD .Bimmergeeks .. XHP Flashtool. ODIS-e.XDelete.THOR-the M Flasher.PRO- Tool and other mobile apps.
7. M6+ Pro supports vehicles with DOIP communication protocol, such as the new Volkswagen, Audi, Skoda, Bentley, Lambo, etc. A dedicated transition button is provided.
8. Support new models such as W223 c206 213 167.
9.Best Replacement of Super MB Pro M6+ and SD C4
10.Xentry W204, DAS W211, HTTWIN, W140 Tested OK
11.Support the old cars and new 12v car, 24v diesel truck & bus, MPV etc
 
Product Functions:
 
M6+ Pro, M6+ and M6 product function comparison chart
 

	M6 Product Functions	M6+ Product Functions	M6+ Pro Functions
XENTRY	√	√	√
XENTRY Truck	√	√	√
DTS	√	√	√
VIDEO	√	√	√
MB DOIP	√	√	√
MB WIFI	√	√	√
PC USB	×	√	√
PC RJ45	√	×	√
Vehicle Voltage Real-time Display	×	×	√
BWM Aicoder	×	√	√
BWM E-SYS	×	√	√
BWM APP	×	√	√
Other DOIP	×	√	√

 
M6+ Pro Connection Instructions


 
1. Connection between MB diagnostic software and hardware
 
(1)Connect the M6+ Pro hardware box to the car diagnostic interface via the test line. The red indicator light ① on the host is always on, and the system indicator ② is flashing during startup. After startup, ② is always on and beeps once, indicating the startup is finished.
(2)Wired connection: Connect the USB port ⑦or the RJ45 port⑧  of the M6+ Pro hardware box to the USB or the RJ45 port of the computer or tablet via a USB cable or a ethernet cable, and a new network connection will appear on the network management interface of the computer or tablet (WIN10 driver-free), and the IP address of the network connection property will be changed to 169.254.255.*, Subnet mask: 255.255.0.0, Default gateway 169.254.255.255, Preferred DNS: 169.254.255.255, click “Advanced”, add multiple IP addresses as 172.29.127.*, 255.255.0.0. After the computer or tablet is connected to the network, ④ the indicator light will be on.

(3) Wireless connection: You cannot find the wireless network by plugging in the USB cable. Unplug the USB cable from the M6+ Pro hardware box port, and you will find a M6+ Pro DOIP-**** network on the computer or tablet, just connect it. ⑤ The green light of the wireless indicator is always on, the wired light is off, no setting is required, the password is 123456789.
(4) After opening the BEN software lock on the computer side, the original diagnostic test software can be used normally.
(5) For remote C-end operation, please consult us.
 
2, Connection between BWM software and hardware  
 
(1)Connect the M6+ Pro hardware box to the car diagnostic interface via the test line. The red indicator light ① on the host is always on, and the system indicator ② is flashing during startup. After startup, it is always on and beeps once, indicating the startup is finished.
(2)Wired connection: Connect the USB port ⑦or the RJ45 port⑧  of the M6+ Pro hardware box to the USB or the RJ45 port of the computer or tablet via a USB cable or a ethernet cable, and a new network connection will appear on the network management interface of the computer or tablet (WIN10 driver-free), and change the network connection attribute IP address to 169.254.255.*, Subnet mask: 255.255.0.0, Default gateway 169.254.255.255, Preferred DNS: 169.254.255.255, Click “Advanced” and add a multi-IP address as 169.254.0.* 255.255.255.0. After the computer or tablet is connected to the network, the indicator light ④ will be always on. Press and hold the switch button ⑩ on the side for 3 seconds and then release it. You can see that the ④ green indicator light is always on and then flashing, indicating that the test can be performed normally. It will return to the initial state after it is powered on again.
(3)The wireless network can NOT be found by plugging in the USB cable. Unplug the USB cable from the M6+ Pro hardware box port, and you will find a M6+ Pro DOIP-**** network on the computer or tablet. You can connect without any settings, and the password is 123456789, ⑤The wireless indicator green light is always on, ④The wired indicator is off. Press and hold the ⑩ switch button on the side for 3 seconds and release it, you can see ⑤the wireless green indicator light is always on and turns to flashing, indicating that the test can be performed normally. It will return to the initial state after it is powered on again.
(4) The computer-side BWM software adopts wired or wireless connection, and the mobile phone BWM APP software adopts wireless connection.
(5) For remote C-end operation, please consult us.
 
3. For DOIP function and hardware connection of other diagnostic test software, please refer to BWM software and hardware connection method.

M6+ PRO Mercedes-Benz and BMW configuration
 
1. Plug the M6+PRO into the power supply or connect the OBD to the test vehicle, and plug in the USB/LAN cable of the M6+PRO.
 
2. Turn on the computer and plug in the computer USB/LAN cable.
 
3. Open the computer network configuration interface and find the Realtek USB FE Family Controller network/the network adapter that comes with the PC.


4. Click “Properties”--TCP/IPV4, and set the IP address as shown in the figure below.


 
5. Click “Advanced”, and add a group of network IP addresses as shown in the figure below.


 
6. Click “OK”. After the configuration is successful, the display is as follows.


 
7.For the same computer, if you replace a new M6+PRO, you need to reset the IP address. After the setting is completed, the computer is successfully bound to the M6+PRO and there is no need to set the IP address again for wired and wireless Internet access. (Use LAN port connection mode, no need to re-set IP when changing devices).
 
8.You can test Mercedes-Benz normally. Please connect the diagnostic cable with SUPER MB PRO logo.


       
9. BMW wireless BMWAiCode configuration(only for F+G chassis)
Connect to the M6+PRO -***, password：123456789, wirelessly, press and hold the M6+PRO switch button for 3 seconds, and the M6+PRO host wireless indicator will flash. The computer-side BMWAiCoder configuration is as follows:


   
10. BMW wired BMWAiCode configuration(only for F+G chassis)
Connect the USB/LAN cable, press and hold the M6+PRO switch button for 3S, and the M6+PRO host wired indicator light will flash. The computer-side BMWAiCoder configuration is as follows:


 
11. BMW wired and wireless E-Sys configuration(only for F+G chassis)
Connect to the M6+PRO -*** wirelessly, press and hold the M6+PRO switch button for 3 seconds, and the M6+PRO host wireless indicator will flash. On the computer side, select the following for direct connection. Wired is similar, no setup required.


 
12. BMW wired ISTA configuration(only for F+G chassis)
  Connect the USB cable, press and hold the M6+PRO switch button for 3S, and the M6+PRO host wired indicator light will flash. The computer ISTA configuration is as follows:


13. BMW Wireless ISTA configuration(only for F+G chassis)
  Connect to the M6+PRO -*** wirelessly, press and hold the M6+PRO switch button for 3 seconds, and the M6+PRO host wireless indicator will flash. The computer side is selected as follows:



14.The mobile phone BWM APP adopts wireless connection. (only for F+G chassis)
Connect to the M6+PRO -***, password: 123456789, press and hold the M6+PRO switch button for 3 seconds, and the M6+PRO host wireless indicator will flash.
 
15. Supported BMW models and years.
 
 
M6+ and M6 product function comparison chart
 

	SD C4 Plus	Super MB PRO M6	Super MB PRO M6+ pro	OEM BENZ C6
Image
Update	HDD/SSD	HDD/SSD	HDD/SSD	HDD/SSD
OEM Compatibility	√	√	√	√
Programming	√	√	√	√
Diagnosis	√	√	√	√
XENTRY	√	√	√	√
XENTRY Truck	√	√	√	√
DTS	√	√	√	√
Vediamo	√	√	√	×
MB DOIP	√	√	√	√
MB WIFI	√	√	√	√
PC USB	√	×	√	√
PC RJ45	√	√	×	√
BWM Aicoder	×	×	√	×
BWM E-SYS	×	×	√	×
BWM APP	×	×	√	×
Other DOIP	×	×	√	×
Cooling	Heat Sinks	Heat Sinks+Fans	Heat Sinks+Fans	×
Old Mercedes	√	√	√	×
New Mercedes	√	√	√	√

 
 
Product Accessories Comparison Chart
 

SKU	Accessories
SP586	1pc x SUPER MB PRO M6+ Pro Host 1pc x OBD2 16pin Cable 1pc x USB Cable 1pc x 38PIN Cable 1pc x 14PIN Cable 1pc x 4PIN Cable
SP586-C	1pc x SUPER MB PRO M6+ Pro Host 1pc x OBD2 16pin Cable 1pc x USB cable
SP586-B	1pc x SUPER MB PRO M6+ Pro Host 1pc x OBD2 16pin Cable 1pc x USB cable 1pc x 14PIN Cable

BENZ Software includes:

Mercedes-Benz Xentry/DAS sedan version 2024.12, truck version 2024.07, supports bus and truck detection (system windows10 64bit)
Maintenance information: WIS September 2021 independent version
Accessories query: EPC November 2018
StarFinder 2024
StarFinder 2016
PL76 accessories price query January 2022
SDmedia offline version January 2014
Engineer version Vediamo 5.01.01
DisassembyAssistant: Disassembly assistant software
Selit service document: self-service document version 14.i
Engineer version: DTS 8.16.15, 9.02
HHWIN old car testing software

V2023.12 BMW Software includes:

ISTA-D 4.41.30
SDP database 4.41.30, Multilingual
VIN:  2023.05.10
ISTA-P  70.0.200, supports BMW motorcycle and electric vehicle programming.
for BMW ETK  2019.11
INPA 5.06, winkfp 5.3.1, NCS 4.0.1
BMWAi Refresh Hidden 4.6  
E-SYS V3.35.3, database V71.0, Chinese version software added
E-sys PLUS 3.81
DR.GINI B022
The latest FSC navigation code software and IBAC coder

Second-hand Panasonic FZ-G1 I5 3rd generation Tablet 8G without Hard Disk
Second Hand, 90% New, Fully Functional.
Basic Information:
Name: Desktop-1KA03JR
Operating system: Windows 10 Enterprise LTSC 64-bit(10.0, Build 19044)
Language: English
System Model:FZ-G1AAHJFLM
Processor: Intel(R)Core(TM)i5-3437U CPU @ 1.90GHZ(4 CPUs), ~2.4GHZ
Memory: 8192MB RAM
Note: The tablet uses a SSD with mSATA interface.

Package Includes:

1set x SUPER MB PRO M6+ Pro
1pc x Second-hand Panasonic FZ-G1
1pc x BENZ +Bmw software 

About Delivery

EU Warehouse Shipping: 3-5 working days. We have stocked up hot sale items in EU(Czech) Warehouse ,which is more convenient for you. Free TAX, faster shipping with cheaper price. 

Yanwen Express:  9-14 working days ,we will prepay the tax,then do not need customers to pay tax for most european counties
( We will send by Yanwen Express by default because of EU high Customs tax. If Customers need the faster DHL shipping method and willing to pay the high tax .Pleasee leave message to us in time after placing the order)

DHL Shipping: 3-5 working days, To help you clearance we will help declare a lower price on the invoice. If address is remote area, customer need pay remote freight or we will ship by Normal Post or Yanwen Express.


Note:
1.All of the items will be shipped to PAYPAL Shipping Address,please confirm your address on PAYPAL before you buy.
2.Your order will be usually shipped out the same or next business days once the payment is made, except on weekends and holidays.


Contact information:

Email: Sales@DiagOBD2.de
Skype: diagtool.de
Mobile:+86 15223201143
WhatsApp: +86 15223201143


Handy Version: Bitte scannen das Bild, koennen Sie per Handy Kaufen!!!