PCMtuner tool can read and write ECU data through OBD, BENCH, and BOOT modes. PCMtuner performs a complete backup of ECU data, easy ECUs clones, and power upgrades. It can also support read and write gearboxes. According to the data read out via PCMtuner tool, our engineers can provide customers stage1 stage2 stage3, popbangs ,gearbox data to adjust LC, sport display, immo off, adblue off, dpf off, dtc off, vmax, swirl off, restoring ECU or TCU factory setting service (paid service).
GODIAG GT100 ist eine neueste Testplattform für die Erkennung der OBDII-Protokollkommunikation und die Wartung / Diagnose / Programmierung / Codierung des Steuergeräts. Es kann die Auto-OBD2-Schnittstelle zur Signalerkennung und zur Umwandlung des elektrischen Pegels in einen 16-poligen umwandeln. Kann einzelne Module oder mehrere Module des Fahrzeugs verbinden.
OBDSTAR DC706 ECU tool, with 1-year free upgrade, is designed for vehicle ECM, TCM and body/other system for ECU flasher. It can read ECU info, R/W Eeprom/Dflash/Pflash/MAP, reset ECU(Virgin), calibrate mileage, read IMMO pincode, ECU recovery... It's all by OBD or bench mode and makes ECU cloning easy.
Godiag GT107 DSG Gearbox Data Read/Write Adapter for DQ250, DQ200, VL381, VL300, DQ500, DL500 TCU
Master version, full protocols, VR reading online
Free update. No subscription, no annual fee.
Auto checksum, Two Years Warranty.
Winols damos and A2L supply for free.
Support Multi-language Deutsch
Dongle contains 67 software modules.
Compatible with Old KTM BENCH
Read and write ECU data without disassembling the ECU using the OBD2 Bench or GTP Bench method or disassembling the ECU and using the Boot method.
Equipped with a short-circuit-proof BOOT resistance board connection line to protect the ECU, you can use it with J2534 devices and PCMFLash software.
This is Bundle Deals for FoxFlash Master Version Super Strong ECU TCU Clone Chip Tuning Tool with OTB 1.0 Expansion Adapter
BDM Frame with Adapters Set made of HQ stainless steel is suitable for BDM Programmer/CMD 100/KESS V2/Ktag/ Fgtech.<br />BDM Frame with Adapters Work for KESS V2/Ktag/ Fgtech
ECU Open Tool For Kess Ktag Fgtech chip tuning tool. Kess Ktag Fgtech ECU Cover Extractor Car Computer Removal Tool designed to remove/ install car ECU computer cover easily. Kess Ktag Fgtech ECU Opening Tool works perfect with ECU Chip tuning tools.
CG100 PROG Airbag Restore Devices Plus ATM adapter with 35080 EEPROM and 8pin Chip reading and writing
CG100-airbag tool exclusively designed to read Tricore MCU’s over CAN-bus.Supports Read/Write EEPROM function for secured and non-secured SAC-TC1766 SAC-TC1767 SAC-TC1796 SAC-TC1797 microcontrollers.comes with Mileage, DPF, ECU system time, ISN built-in calculators.Edit CRC Eeprom.
The ATM adapter suppports 35080 35160 DQW080 DQW160 35080V6 VP, parallel FLASH Zhiwei anti-theft cancellation,8-pin chip,ATMEGA re-use.
FC200 supports 4200 ECUs/EGS, covers 80% of models in the market. No open shell, no punch, keep the original parts.
Data loss prevention, automatic verification, 100% accurate analysis of BMW ISN code, supports VIN code modification, and data cloning of various models
Exclusive support for DTC shielding and function shutdown, exquisite design, adapt to various operating environments, FC200 is your trusted auto repair assistant
CGDI EGS & FCU Testing Cable for Benz/BMW//VW/Audi Work with CGDI BMW
GODIAG ECU IMMO Prog AD GT105 is equipped with PWM+(PIN2), CANH(PIN6), CANL(PIN14), K-line(PIN7) signal communication indicators. When there is data communication, the corresponding protocol indicator will flash, therefore the communication status can be judged and you can also determine whether the diagnostic programming device is able to communicate.
FoCOM is diagnostic program for Ford vehicles. It can connect to various electronic control units (ECUs) and display identification, read and clear fault code memory, display and record measured values and perform actuator tests.
This is PCMtuner ECU Programmer 67 Modules in 1 + GODIAG GT107 DSG Gearbox Data Read/Write Adapter with GT105 + Breakout Tricore Cable,complete kit
PCMtuner Fetrotech Tool Support MG1 MD1 Black Color Stand-alone Device
Support MG1 MD1 ECU and BENCH Read MED9 and EDC16, and also support MEDC17 series
Free Update Online, No Annual Fee
CG FC200 ECU Programmer Full Version with New Adapters Set 6HP & 8HP / MSV90 / N55 / N20 / B48/ B58/ No Need Disassembly
More than 98% of ECUs support BENCH mode and OBD mode, no need to open the cover and punch holes to protect the original car.