New KT200 ECU Programmer Full Version
The New KT200 is mainly used to read and write ECU and TCU. The product is mainly designed for refit shop, repair shop, auto electronics repair merchant.
Free Send Toyota Lexus BDM/JTAG Solder-free Adapter--SO664-B
Top Reasons to get New KT200:
1. Master version
2. VR read online work (some ecu need use our VR system, tool auto connect to ousr server donload file )
3. Free update. No subscription, no annual fee.
4. ECU can be restored to original if your ecu was damage or meet some bad tuning, use our tool can restore to original.
5. Tool can online and offline work (some of ecu and functions can offline)
6. Online support
7. Two Years Warranty.
8. Excellent technical support.
9. Help desk and tuner account
10. ECU and TCU connect wires with pdf
11. Auto checksum. Auto support eeprom and flash checksum
12. Support MEDC17 free clone service (most of others tool need patch the files after read out ,but ours is free)
13. Multi-language:
Dutch(German), Italian, English, French, Spanish, Polish, Portuguese, Romanian, Czech, Turkish
14. Protocols activated: Car OBD, Truck OBD, Tractor OBD , Boat OBD, Motorbike OBD ,BDM/JTAG , TOOL BOOT, Bench Mode, TCU Gear
15. Software free download
www.ktmtool.com
16.
Compatible operating systems: Windows 7 /8/8.1 /10/11 pro/ultimate , CPU > 2.5 GHz (Intel i5, i7), RAM > 8GB
Product Functions:
New KT200 support OBD, BENCH, Jtag, Boot, BDMmodes.
1: OBD mode:(read the data from Diagnostic port, you need remove the ecu or tcu from car or open the ecu box, just read everything from car, we also support obd reading, we supply original file from our server, you can read it via obd reading. )
2: BENCH mode: we also call it service mode, you can use this mode clone or backup all ecu data, read the internal flash and external flash and eeprom data, so you can save a lot of money for clone ecu and tcu , you also can clone tcu and chiptuning with this mode.
3: Jtag mode: open the ecu, and wire it or use ours adapter to connect ecu ways,some of denso ecu always need use this mode for reading and writing .
4: Boot mode: open the ecu and always can backup everything, read the flash and eeprom, you can save some ecu cause your obd write failed, or some
5: BDM mode: some of the ecu need read and write in bdm mode, open the ecu and use ours adapter to connect it.
New KT200 Supported Functions:
ECU clone
TCU clone
Chiptuning
Stage1-stage4
Vmax off
Adblue and SCR off
DPF OFF
Flaps OFF
popbangs
gearbox data to adjust LC
sport display
immo off
dpf off
dtc off
GPF/OPF Removal
DPF Removal
EGR Removal
DTC Removal
ADBlue Removal
HOT Start Fix
IMMO Removal
Readiness Calibration
Flaps / Swirl Removal
TVA Removal
Sport Displays Calibration
Cold Start Noise Reduction
Kickdown Deactivation
StartStop Disable
MAF Removal
Speed Limiter Removal
Torque Monitoring Disable
Burbles Activation
Popcorn Activation
EVAP Removal
Exhaust Flap Removal
SAP Removal
AGS Removal
BMS/BPCM
Lambda/O2 Removal
Launch Control
OBD Reading Protection
Boost Sensor Calibration
LC, AL and NLS for MED9.1
Checksum Fix
vmax, swirl off
restoring ECU or TCU factory setting service
VIN fix (EEPROM support checksum, so you can easy change VIN then write back)
Instructions for using KTsuit:
Do following work before starting our tools
A:Connect your KTsuit with USB cable to laptop
B:laptop or PC must connect to internet
Step1: go to www.ktmtool.com website donwload the software,install the package.
Step2:Check the SN where tie on your box backside , noticy : dont realase that SN to anyone , its a safe code for you ,dont let any third party or guys know that code or it easy let your tools lock.
Step3:Send that SN to email: info@ktmtool.com for active and link your tool to your email .(you tool will be lock if you dont send to active)
Step4:run the ktsuit manager, and register it with your email , then input the sn active your account, don’t close the ktsuitmanager before your run ktsuit ,always keep click the active button before you run the ktsuit software.
Step5: input that SN code to you login windows when you run KTsuit main software, it will ask you input that code ,then you software and tool will be online.
KT200 Package List:
Hardware:
1pc x Master machine
1pc x KT200bench box
1pc x USB cable
1pc x Power adapter
1pc x Fox box store over 10 adpaters
1pc x Jtag and bdm cables
1pc x Pen
1pc x Notebook
1pc x Carton case
1pc x Function cable for boot, bench, kline links .
1pc x Truck OBD cable
1pc x Car OBD cable
1pc x Paper box
1pc x Install guide
Software:
1pc x Main software
1pc x Technical Support
1pc x Login account for software and tools
1pc x PDF pacakges for connecting ecu and tcu
1pc x Join facebook group for support
1pc x Online chat support for use
Extra pacakge according to users request after the user get the tool.
1pc x Tuner account
1pc x Helpdesk
1pc x WinOLS damaos, A2L